镍代钴矿用硬质合金的新进展

概述了镍代钴矿用硬质合金的国内外进展情况．     

制备W－Ni－Cu钨合金的热解还原法工艺探讨

用硝酸镍、氯化铜与乙酸镍、乙酸铜的溶液分别与钨粉混合，干燥，经热解还原法制备的Ｗ－Ｎｉ－Ｃｕ钨合金，其技术指标均可满足使用要求。文章分析、讨论了这两种工艺特性及存在的问题。采用硝酸镍、氯化铜代镍、铜所制备的钨合金，在热解还原过程中产生大量有毒气体、严重的污染环境。乙酸镍、乙酸铜代镍和铜制备的钨合金，在热解还原过程中较好地解决了对环境及产品的污染问题，并保持了热解还原工艺的特性。     

化学沉积Ni-P及Ni-Cu-P合金镀层晶化行为的比较

利用DSC和XRD对化学沉积Ni-P及Ni-Cu-P合金镀层的晶化行为进行了比较研究，结果表明：低磷Ni-P镀层直接转变为稳定相Ni3P,而低磷（高铜）Ni-Cu-P镀层则经生成亚稳中间相Ni5P2后再向稳定相Ni3P转变，高磷非晶态Ni-12.1%P(质量分数，下同）和Ni-17.96%Cu-9.29%P合金镀层均先形成亚稳中间相Ni5P2和Ni12P5后，再转变为稳定相Ni3P,但Ni-Cu-P合金镀层转变为亚稳相的温度比Ni-P镀层的高。     

粉末布法制备SiC/Ti基复合材料

用粉末布法制备了低成本SiC/Ti基复合材料.结果表明,采用合适的轧制参数即可容易地获得厚度合适、均匀的粉末布;热失重分析和热解残余物分析指出用来制备粉末布的有机粘结剂的去除过程分成两个阶段,合理除气后,基本没有残余物.使用真空热压工艺制备的SiC/Ti基复合材料,纤维分布基本均匀,纤维与基体的界面结合良好.     

钛及钛合金中氧和氢的联合测定

叙述了用红外吸收法对钛及钛合金中氧和氢联合测定的方法，取得了测定的最佳条件。连续测定6次的相对标准偏差在10％以下，作加标回收试验的回收率为95．6％～103．9％。分析时间在3min以内，可应用于日常分析，结果满意。     

热强钛合金BT25组织与性能

介绍了前苏联航空发动机用热强钛合金（或高温钛合金）BT25的发展概况，并对BT25合金的成分特点、热处理强化优点等做了进一步阐述，给出了退火状态下的物理性能，在说明热强钛合金微观组织与力学性能关系的基础上给出了BT25合金的各种力学性能。     

稳定锐态型钛白粉分散性能工业试验

试验分别用水性分散剂和油性分散剂对钛白粉半成品进行粉碎包膜，检测成品的应用性能，发现水性分散剂效果不明显，而油性分散剂对分散性和分散稳定化程度都有提高，同时分析了在锐态型钛白粉行业产品包膜效果的影响因素，以供参考。     

亚稳态金属材料抗空蚀性能研究

用旋转圆盘实验机研究了三种金属材料的空蚀。试验结果表明 :Fe -Mn -Si形状记忆合金、Fe -Cr-Ni-Mn不锈钢空蚀中分别诱发产生密排六方晶体结构的马氏体和体心立方晶体结构的马氏体 ,其抗空蚀性能依次为 0Cr13Ni5Mo不锈钢的 7.3倍和 2 .1倍。亚稳态金属材料抗空蚀性能与空蚀过程中动态相变对应力的响应密切相关。空蚀诱发马氏体相变不仅有利于改善材料抗空蚀性能 ,而且马氏体相变及其逆转变引起的能量耗散和伪弹性大大提高了Fe-Mn -Si铁基形状记忆合金的抗空蚀性能     

Corrosion fatigue of extruded magnesium alloys

Corrosion fatigue tests were carried out on extruded AZ31 (3% Al, 1% Zn, 0.3% Mn, Mg—the rest), AM50 (5% Al, 0.4% Mn, Mg—the rest) and ZK60 (5% Zn, 0.5% Zr, Mg—the rest) Mg alloys in air, NaCl-based and borate solutions. N_sol/N_air ratios (the relative fatigue life) were used for the analysis of the corrosion fatigue behavior of Mg alloys in various environments, where N_sol and N_air are the numbers of cycles to failure in the solution and in air, respectively. Extruded ZK60 alloy reveals very high fatigue and corrosion fatigue properties in comparison with other alloys. However, it has the lowest relative fatigue life (N_sol/N_air 10⁻³–10⁻²) or the highest sensitivity to the action of NaCl-based solutions in comparison with that of AM50 and AZ31 alloys (N_sol/N_air 10⁻²–10⁻¹). Under the same stress, the corrosion fatigue life of extruded alloys is significantly longer than that of die-cast alloys (N_sol for extruded AM50 in NaCl is two to three times longer than that of die-cast AM50).     

On the specific reactivity of platinum segregated layers on Pt80X20 (111) (X= Ni,Co, Fe) alloys

The influence of alloying of Pt with 20 at.% of Ni, Co and Fe has been studied in the hydrogenation of 1,3 butadiene. Iron induces the more important modifications, with both higher activity and selectivity. The results are discussed in terms of the surface segregation, the local order in surface and the electronic properties measured by photoemission of core levels.